Marquis 545 Owner's Manual download pdf (Page 5)

E - S E R I E S H O T T U B S

O W N E R ’ S M A N U A L

STARTING YOUR SPA

START-UP PROCEDURE

Your spa is equipped with solid-state Comfort Controls specific to your spa

model. (See SPA CONTROL OPERATION for your specific spa model.)

To start your spa, you need a spa water test kit or test strip and an underwater

thermometer. It is important to follow each of these steps when starting your spa.

Once you have completed the following steps, refer to the instructions in your start-

up kit for proper start-up water maintenance, or see MARQUIS SPA CARE.

NOTE: Your spa has been filled and test-run at the factory. The first time your

spa is filled with water, some discoloration from residual test water may appear.

This will disappear when the spa is completely filled and the filtration system is

functioning.

WARNING: Spa must be completely filled with water before turning on power.

Test the water for the proper chemical balance and adjust as necessary.

Marquis SpaCare™ products are recommended. (See WATER TREATMENT.)

PROPER CHEMICAL BALANCE IS IMPORTANT for your safety and the

longevity of your spa.

In the case of relocating your spa, it is imperative to follow the instructions in the

owner’s manual. These instructions must remain with the spa. Damage caused

by relocating spa is not covered under warranty.

THERAPY PUMP(S)

Start-up procedure for all models

1. Place spa on a hard, flat, level surface. Make sure the power supply is

off.

2. Make sure the suction guard(s) in the footwell are in place and

undamaged.

3. Open the equipment door. Tighten all disconnects and open all shut-off

valves.

NOTE: Keep the drain valve closed at all times except when draining the spa

(do not rely on the cap to stop the flow of water). Not doing so could

result in damage to the drain valve due to freezing water.

4. Install filter cartridges. (See INSTALLATION INSTRUCTIONS, Filter

Cartridges.)

5. Fill the spa with water to two-thirds of the way up the Vortex skimmer

openings.

The use of a Fill Filter is recommended, especially in areas with high

mineral content in the water.

6. Turn the power on.

7. Your spa is now displaying “LINK” in the LCD window on the control

panel.

8. Press the TEMP button to start the spa and LINK will disappear.

9. The spa is now displaying “RUN PMPS PURG AIR” in the LCD

window, press the JET 1 button to run the pump and purge the air from

the plumbing.

10. After a few minutes the system will go into standard operations.

11. The temperature factory default is 37°C; you can change the tempera-

ture by pressing the TEMP button. The maximum set point is 40°C.

ENERGY COVER

When the spa is not in use, the cover should be kept on the spa to retain the

water’s heat and to keep out dirt, leaves, etc. Your Marquis spa must be

equipped with a Marquis energy cover to receive full acrylic shell warranty.

Other covers may not provide adequate protection. Fading and staining of the

spa cover and broken foam cores are not covered under warranty for any

reason. Spa covers do not qualify for labor coverage under warranty. Purchase

or exchange parts under warranty at authorized Marquis dealer.

For your safety and convenience, the cover is equipped with adjustable straps,

safety locks, and handles. Use the exterior handles to remove and replace your

cover. Never attempt to open or remove the cover by grasping or pulling on the

cover skirting or cover lock straps as the skirting will tear.

Marquis suggests you use the safety locks to help keep out unintended users

and prevent covers from being blown off in windy conditions. The cover and

retractable cover system are not recommended for use in wind conditions

reaching above 40 km/h. If your spa is located in an area susceptible to high

winds, additional cover lock straps may be necessary to minimize cover

damage.

Open the spa cover:

1. Unfasten all cover lock straps.

2. Place one hand under the cover skirting, between the spa and cover,

to break the cover’s vacuum seal. Do not use cover handles to break

vacuum seal.

3. Fold the front half of the cover over onto the back half.

NOTE: Unlock and release all cover locks before attempting to open cover.

Damage caused by attempting to open the cover while locked or by wind is not

covered under warranty. Do not walk, stand, climb, or sit on the vinyl cover or

retractable cover system. Do not use hard, sharp, or metal objects, such as a

windshield scraper, to remove ice. Such objects can cut, mar, or puncture the

cover’s vinyl surface.

Close the spa cover:

1. Place one hand on the upper corner of the cover and gently push

forward in the direction of the spa. The cover will rotate forward to

cover half of the spa.

2. Unfold the cover by lifting the handle located on the top (front) half of

the cover. Allow the unfolded half to fall down onto the spa.

3. Secure the cover lock straps to the spa and lock them.

NOTE: When opening a cover with a cover removal mechanism, use one of the

manufacturer’s recommended methods. Do not attempt to open the cover in any

other way. Damage caused by improper opening or closing of the cover is not

covered under the warranty.

Fading, staining, torn stitching of the spa cover and broken foam cores are not

covered under the warranty for any reason. Spa covers do not qualify for labor

coverage under the warranty. These parts can be purchased or exchanged

under warranty at your authorized Marquis Spas

dealer.

1 2 3 4 5 6 7 8 9 10 ... 21 22

Comments to this Manuals

No comments

Marquis 545 Owner's Manual Page 5

Comments to this Manuals