WARNING: If the information in these instructions is not followed exactly, a fire or explosion may result causing property damage, personal injury or
I26CV Clean View and Surround Sizes *The Clean Views and Surrounds in this section must be used with Valve Control Components inside the opening (as s
I26CV1DS IDV26 *The Clean View Designer Door and optional surround in this section must be used with Valve Control Components inside the ope
IDV26 I26SU Universal Surround A Universal Surround is available for the IDV26. This is provided as a flat sheet which mounts onto the unit and i
I26SU UNIVERSAL SURROUND I26CVPFI26CVPF2BOTTOM OF UNIT 13
I26CV - Surround Installation -Clean View (CV) Attachment -Valve Access 1. Optional Surround Kit (I26S, I26SPF, I26SU) is fastened to the
I26S1 / I26SPF1 / I26SU Surround Installation Component List: I26S1 / I26SPF1 / I26SU Surround, [Qty 4] #6 Black Combo Screws Bend Up All 4 Mount
I26CV2 / I26CVPF2 Wide Clean View Installation Component List: I26CV2 or I26CVPF2 Clean View On/ Off Switch Extension Bracket Fan Control
I26CV2 / I26CVPF2 Wide Clean View Installation -Components Out- Fan Control Switch Bracket On/Off Switch Bracket Remove On/Off Switch and original
IDV33 Insert Dimensions and Sizing I33CV Clean View and Surround Sizes Min. Coverage with Optional I33LK or I33CV Base Unit I33LK I33CV F
I33LK Louver Kit and Surround Sizes NOTE: The Surrounds shown here are universal and can be used with the I33CV model. Furthermore, the I33S4535B a
Pre-installation Questions and Answers About curing of the paint Your stove or fireplace has been painted with the highest quality silicone stove pa
IDV36 Insert Dimensions and Sizing I36CV Clean View and Surround Sizes Min. Coverage with Optional I36LK or I36CV Base Unit I36LK I36CV Fro
I36LK Louver Kit and Surround Sizes NOTE: The Surrounds shown here are universal and can be used with the I36CV model. Furthermore, the I33S4535B
I33CV/I36CV Front Face and Surround Attachment Installation 1. Remove the Top Filler Panel to install vent adapter and venting to the unit. Once th
I33LK/I36LK Front Face Attachment Installation 1. Remove the Top Filler piece from the Base unit by unfastening its three [3] screws. This part is
Surround Installation for IDV33/IDV36 Fronts 1. Ensure that the I33LK/I36LK Front is installed before continuing with these steps. 2. When instal
IDV26 / IDV33 / IDV36 Wall Coverings All wall coverings below Combustible Mantel Line MUST be Non-Combustible (e.g. steel studs and con
IDV26/IDV33/IDV36 Clearance to Combustible Mantels Before installing any mantels it is important to determine the combustibility of its material(s).
IDV26 / IDV33 / IDV36 Venting This appliance must not be connected to a chimney flue serving a separate solid-fuel burning appliance. This appl
IDV26 / IDV33 / IDV36 Installation of Vent Pipe 1. Remove the Top Filler and adapter plate from the unit by removing the five [5] screws as shown
Insulation of Chimney Cavity IDV26 / IDV33 / IDV36 If You Live In A Cold Climate Zone And Your Chimney Is On The Side Of Your House In cold cl
Table of Contents Pre-installation Questions and Answers...
IDV26 / IDV33 / IDV36 Riser Kit and Leveling Instructions Leveling Instructions When installing insert it may be necessary to support back of unit. T
IDV26 / IDV33 / IDV36 Glass Door Information Glass Cleaning It will be necessary to clean the glass periodically. During start-up condensation will
IDV26PRL - Porcelain Liner Panels- To Remove: 1. Remove Log Supports. Remove the [5] screws in the firebox top holding the Baffle in plac
IDV26RL - Brick Liner Panels- To Install: 1. Remove the Baffle. Remove the [5] screws in the firebox top holding the Baffle in place. Rem
IDV33 / IDV36 Brick Liner and Liner Panel Installation Instructions For IDV33 & IDV36 Brick Liners 1. Remove the glass door. If a flat black re
IDV33/36PRL- Removing and Installing Generation 2 Liner Panels- To Remove: 1. Lift Log Supports out of fireplace. 2. Remove the 2 Screws in the
IDV33/IDV36 Overlay and Double Door Installation IDV33 Overlay This style of Overlay mounts in the square notch cutout as shown in the illustration
Gas Line Installation This gas appliance should be installed by a qualified installer in accordance with local building codes and with current CAN/C
IDV33 / IDV36 Burner Installation/Removal Burner System 1. Remove glass door assembly and logs (if installed). Be careful with logs as they becom
IDV26 Burner Installation/Removal Burner Pan Removal Step 1: Disconnect pilot lines and gas supply line from valve on the side of the unit. NOTE: C
Millivolt System, Lighting, and Burner Control... 4
IDV26 -Millivolt- -Control Components Outside the Opening- -COMPONENTS OUT- This procedure must be done Before the unit is insi
Fasten Component Panel at top. Replace Side Plate. Attach Component Panel and Extended Switch Bracket. Procedure is complete. IDV26 -IPI- -C
Replace Side Plate. Fasten Component Panel at top & bottom. Attach Component Panel and Extended Switch Bracket (see millivolt section). Procedu
IDV26 Fan Speed Control Outside COMPONENTS OUT NOTE: It is not necessary to disconnect fan wiring to complete this procedure. This procedure
IDV26 Optional Fan Removal / Installation The fan can be accessed from the back of the unit (which is easiest on an uninstalled unit) or throu
IDV26 Fan - Wiring IDV26 45
IDV33 / IDV36 Fan Installation/Removal IDV33 / IDV36 Fan System WARNING Electrical Grounding Instructions This appliance is equipped with a thr
IDV33/IDV36 Insert Burner Component List ITEM NO. PART DESCRIPTION Qty. 1 3620-105 Burner Bracket 1 2 3620-105L Burner Bracket 1 3 DVI33-107 B
Millivolt System, Lighting, and Burner Control FOR YOUR SAFETY READ BEFORE LIGHTING BEFORE LIGHTING A This appliance has a pilot which must be ligh
IDV26 Remote Receiver Location All Units Connecting to the Gas Valve The wiring harness for the Proflame GTM system has two wires labeled “TH” &
Mobile Home/Manufactured Housing Installation This Direct Vent System Appliance must be installed in accordance with the manufacturer’s installatio
IPI Electronic Ignition System Overview The IPI system is an advanced burner controller that provides you with the option of having either a Standing
IPI Electronic Ignition System the receiver and then press the power button [5] on the transmitter. An audible beep will sound to indicate the system
IPI Electronic Ignition System Configuration #1: Basic manual HI/LO and manual ON/OFF capabilities. Configuration #2: Remote ON/OFF and manual HI
Electronic Ignition Lighting Instructions If you do not follow these instructions exactly, a fire or explosion may result causing property damage, p
IDV26 LOGF26 DC BAA B C D 1 1 2 23 3 4 455 7 6 76891010 889 WARNING: Failure to position the parts in accordance with these diagrams o
IDV26 LOGF27 1 2 3 4 56 ABC D1 23 45 6 4ABC D WARNING: Failure to position the parts in accordance with these diagrams or failu
Log Placement – LOGF35 LOGF35 Log Set and Glowing Embers Parts List This illustration shows the rear log positioning bracket and 4 pin locating posi
Log Placement – LOGF36 LOGF36 Log Set includes Glowing Embers, Lava Rock, and Vermiculite. Place Log #1 onto rear log holder and center. Place Log
MQRSP4 / MQRSP8 Rock and Glass Support Platform Installation IDV26 / IDV33 / IDV36 Preparation: Remove Grate Bar and replace screws. Remove Em
RSP10 Glass Support Platform -Installation IDV26 / IDV33 / IDV36 Preparation: Remove Grate Bar and replace screws. Remove Ember Plates. Do not remo
Warnings, Installations and Operations Installation Regulations This gas appliance must be installed by a qualified installer in accordance with local
MQROCK2 / MQROCK3 -MQRSP4 IDV26 / IDV33 / IDV36 MQRSP4 Parts List 1Ea Rock Support 1Ea Ember Plates Assembly Remove the ember plates
MQROCK2/ MQROCK3 -MQRSP4 for IDV26 / IDV33 / IDV36 (continued) Step 4: Place Rocks #6 into position as shown above. Step 5: Place Rocks #3 into p
MQStone MQRSP8 IDV26 / IDV33 / IDV36 Decorative Stone Set. Supplied for MQRSP8 only. Begin by placing larger stones inside burner tu
Glass Ember / MQ Ember Installation -MQRSP8 / RSP10- IDV26 / IDV33 / IDV36 MQ DEALER ONLY Spread glass or ember chunks onto tray and burner. Ensure
Burner System Maintenance It is recommended to annually inspect and clean the Burner System to prevent malfunction and / or sooting. This operation sh
Conversion Kit Instructions – PART A PLEASE CONFIRM THAT STEP 4 IS UNDERSTOOD BEFORE PROCEEDING WITH CONVERSION. WARNING: This conversion kit
Gas Conversion for Top Convertible Pilot (Series 019065X) – PART B Instructions for converting SIT 190 series pilot burner injection from NG to LPG
Gas Conversion for Modulator – PART C -WARNING!- -WARNING!- 67
Troubleshooting the Gas Control System Problem Possible Causes Corrective Action Defective or misaligned electrode at pilot. Check for spark at
IDV26 Parts List Part No. Description Fireplace Base Unit IDV26N [Millivolt] IDV26NE [IPI] INSERT DIRECT VENT FIREPLACE Natural Gas 30,000 BTU IDV26
• Gas fired appliances may be used only for supplemental heat and/or decorative purposes and under no circumstances shall they provide a primary heat
VI30GBL Grill Kit – Black Fireplace Accessories for IDV33 (Both Front Kits) Door Frame Overlays Z33ADDX Arch Door Frame – Deluxe Black (352) Z33ADTH
Parts for IDV26/ IDV33/ IDV36 Part No. Description Riser Kits I33R40 2-1/2” Riser for use with I33S4028B and I36S3931B I33R44 2-1/2” Riser for use
This Limited Lifetime Warranty applies only while the unit remains at the site of the original installation and only if the unit is installed insi
Important Information INSTALLATIONS The following label (supplied with the gas fireplace insert) must be attached with rivets or screws to the
IDV26 Insert Dimensions and Sizing Top View- Components In (As Shipped) Minimum Opening Dimensions Dimension Components In
Comments to this Manuals